氣體吸附式缺水機

◆廠品特征 Product features

※體現了動態平衡相一致的撒氣重壓和露點

1.降解塔之高寬比與孔徑經科學實驗結果精密機械計算公式，塔床內壓小，絕對了壓解氣物皮膚干燥劑5秒的接受時期，夠滿足制成品氣的露點規定。

2.30％的潮濕劑余下量，用作補償費潮濕劑的大自然損壞，確保安全潮濕。

3.巨型吸附器，確定氣旋均可以通過空氣干燥劑層，徹底消除溝流癥狀。

※重復氣量消耗的資金需小于14％

1.有遠見的機筒設定，上傳100％的吸出熱氣，處理的熱氣廣泛用于加強凈化利用環節的凈化利用氣室內溫度，提高自己機的解吸作用，會讓凈化利用更齊全。

2.吹干和可復蘇采取返向煙囪效應實施方案，濕水汽流下干的活性炭吸附劑期限果比較好。可復蘇氣出來含濕量控制在亞供大于求模式，使消音器原理器及res排氣渠道無結水之慮。

3.可利用干熱機的執行電動機扭矩需求分析的調節降解氣用水量，抓好降解熱空氣累計比較穩定，降解壓力值低至臨介。

※干熱劑使用的耐用度長

1.比較適合的機筒外形尺寸，使氣體利用粗糙劑層的氣速和時段要保持好的情況下，加以發揮作用粗糙劑的機械性能。

2.合情合理的系統化配值，在空氣來到機筒前，經除油解決及時性去掉空氣中內含油量物與重感染物，避免出現空氣干燥劑層受感染。

※機器選用了高大上高品級電動四輪及自己閥和穩定可靠的全電子技術可程序編寫序調整器，組排軟件界面團結，自己間斷性提示雙塔工作，循環往復時間段直播可編，出廠的更改10min。氣動閥門質保期短短50萬次行為。

※封頭罐壁作冷鍍鋅鋼板除銹防銹處置，10年不生繡。

※動作圖片精確性、固定性固定、操控簡變，重新安裝不需要根基。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆主要是技術性叁數 Main technical parameters